Forum Index > Gear Talk > Problem with air in MSR ceramic filter
Previous :: Next Topic  
Author Message
BeardoMcGrath
Member
Member


Joined: 16 Jan 2018
Posts: 65 | TRs
Location: Seattle
BeardoMcGrath
  Top

Member
PostWed Apr 07, 2021 5:14 pm 
Reply to topic Reply with quote
I've used the old-style ceramic MSR filter for years, since they tend to be reliable and you can just go out and buy new ceramic elements as needed. Last fall I started having an odd issue with the filter, where air was somehow getting into the top compartment:

Air gets trapped in the compartment shown. This causes some weird pressure problems and eventually water does not get pulled into the filter.
Air gets trapped in the compartment shown. This causes some weird pressure problems and eventually water does not get pulled into the filter.

While I was on the trip, I found removing the top screw on section would receive the pressure, and then sometimes removing and reinserting the small orange piece (see below) would help, however inevitably air would get back into the mechanism and I'd have to remove the bottom section again. This was suboptimal when trying to refill water.

Removing the orange piece and reinserting sometimes helped.
Removing the orange piece and reinserting sometimes helped.

Interestingly, this started to happen after following the instructions to boil the ceramic element portion of the filter to clean, but I had done that before with no problem so that may just be coincidence. Also I don't understand how any portion of the ceramic filter would be causing the problem. All the rubber gaskets and o rings seem to be in good shape as well, so that also doesn't seem to be the problem.

I plan to try a second new ceramic element just in case there is something wrong with that part, but have in general been happy with this filter and want to avoid buying a new one. However, if people have a good suggest for a lightweight filter with good throughput I would also consider buying something new. Thanks!
Back to top
View user's profile Search for posts by this user Send private message Send e-mail Reply to topic Reply with quote
InFlight
coated in DEET



Joined: 20 May 2015
Posts: 720 | TRs
Location: Seattle area
InFlight
  Top

coated in DEET
PostWed Apr 07, 2021 7:12 pm 
Reply to topic Reply with quote
May just be an aged o-ring thatís leaking. 
Thereís a MSR rebuild kit ($17) on Amazon that has all rubber parts along with some silicon grease that is used. 

I have one of these filters, ití the best choice for any glacial silty water.   Itís a heavy filter, so I use a BeFree for normal backpacking trips.

--------------
ďI went to the woods because I wished to live deliberately...Ē  ― Henry David Thoreau
Back to top
View user's profile Search for posts by this user Send private message Reply to topic Reply with quote
JonnyQuest
Member
Member


Joined: 10 Dec 2013
Posts: 499 | TRs

JonnyQuest
  Top

Member
PostThu Apr 08, 2021 8:40 am 
Reply to topic Reply with quote
You might try calling (or if you're local, visiting), MSR.  They usually provide very good customer service.
Back to top
View user's profile Search for posts by this user Send private message Reply to topic Reply with quote
BeardoMcGrath
Member
Member


Joined: 16 Jan 2018
Posts: 65 | TRs
Location: Seattle
BeardoMcGrath
  Top

Member
PostThu Apr 08, 2021 12:11 pm 
Reply to topic Reply with quote
Thanks both I'll try those options. Replacing the ceramic element seems to be helping, so maybe I just filtered from a silty stream a few too many times...the BeFree filter seems to have a number of positive reviews on here so I'll take a look at that too.
Back to top
View user's profile Search for posts by this user Send private message Send e-mail Reply to topic Reply with quote
hbb
Member
Member


Joined: 06 Aug 2009
Posts: 261 | TRs

hbb
  Top

Member
PostThu Apr 08, 2021 1:43 pm 
Reply to topic Reply with quote
Did you put the filter lower end cap o-ring back on the filter element after boiling?

Try cleaning the duckbill valve and re-lubricating the piston o-ring with silicone grease. There's a schematic on the MSR website that will show you where these parts are. That orange piece is the umbrella valve--you also want to make sure there isn't any grit caught under there. Those are the usual trouble spots for me when I've had similar issues with that model filter.
Back to top
View user's profile Search for posts by this user Send private message Reply to topic Reply with quote
   All times are GMT - 8 Hours
Forum Index > Gear Talk > Problem with air in MSR ceramic filter
  Happy Birthday blue_tuberosa, ASBrauer, jabenoi!
Jump to:   
Search this topic:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
   Use Disclaimer Powered by phpBB Privacy Policy